From fca6f60a44a75f76d2c1183f06466228b01b9686 Mon Sep 17 00:00:00 2001 From: Matthias Schiffer Date: Sat, 12 Nov 2011 12:17:23 +0100 Subject: Allow using [SD]NPTV6 rules in INPUT/OUTOUT chains --- README.html | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) (limited to 'README.html') diff --git a/README.html b/README.html index 7a0674c..159f51c 100644 --- a/README.html +++ b/README.html @@ -1,6 +1,6 @@ -NPTv6 (IPv6-to-IPv6 Network Prefix Translation) for Linux

NPTv6 (IPv6-to-IPv6 Network Prefix Translation) for Linux

Sven-Ola Tuecke

Freifunk

Matthias Schiffer

Freifunk Lübeck

10-NOV-2011

Table of Contents

Installation
DKMS Integration
Configuration
Brief Version
NAT Behavioral Requirements
IPv6/IPv4 Precedence
Change gai.conf

These files implement a Linux netfilter target that changes the IPv6 +NPTv6 (IPv6-to-IPv6 Network Prefix Translation) for Linux

NPTv6 (IPv6-to-IPv6 Network Prefix Translation) for Linux

Sven-Ola Tuecke

Freifunk

Matthias Schiffer

Freifunk Lübeck

10-NOV-2011

Table of Contents

Installation
DKMS Integration
Configuration
Brief Version
NAT Behavioral Requirements
IPv6/IPv4 Precedence
Change gai.conf

These files implement a Linux netfilter target that changes the IPv6 address of packets. The address change is done checksum neutral, thus no checksum re-calculation for the packet is necessary. You can change the IPv6 source address of outgoing packets as well as the IPv6 destination address @@ -53,13 +53,15 @@ ip6tables -t mangle -A POSTROUTING -o eth0 -s FD01:0203:0405::/48 -j SNPTV6 --to will enable this:

ip6tables -t mangle -A PREROUTING -d 2001:0DB8:0001::/48 -j MARK --set-mark 42
 ip6tables -t mangle -A PREROUTING -d 2001:0DB8:0001::/48 -j DNPTV6 --to-destination FD01:0203:0405::/48
 ip6tables -t mangle -A POSTROUTING -m mark --mark 42 -s FD01:0203:0405::/48 -j SNPTV6 --to-source 2001:0DB8:0001::/48
-ip6tables -t mangle -A POSTROUTING -o eth0 -s FD01:0203:0405::/48 -j SNPTV6 --to-source 2001:0DB8:0001::/48

IPv6/IPv4 Precedence

With (EKU)buntu and eventually with RedHat, you will notice that +ip6tables -t mangle -A POSTROUTING -o eth0 -s FD01:0203:0405::/48 -j SNPTV6 --to-source 2001:0DB8:0001::/48

If the router running NPTv6 is offering services itself, additional + rules are necessary for the services to be reachable by the external address:

ip6tables -t mangle -A OUTPUT -d 2001:0DB8:0001::/48 -j MARK --set-mark 42
+ip6tables -t mangle -A OUTPUT -d 2001:0DB8:0001::/48 -j DNPTV6 --to-destination FD01:0203:0405::/48
+ip6tables -t mangle -A INPUT -m mark --mark 42 -s FD01:0203:0405::/48 -j SNPTV6 --to-source 2001:0DB8:0001::/48

IPv6/IPv4 Precedence

With most Linux distributions you will notice that your browser does not show the IPv6 version of a web site that is multi-homed when using ULA addresses for your IPv6 Internet connection. The reason for this is an add on to the RFC 3484 rules that is compiled - into the (EKU)buntu libc. The pre-installed - /etc/gai.conf file will give you a hint on - this.

In short: the getaddrinfo() library function rates a private IPv4 + into the libc. The pre-installed /etc/gai.conf file + will give you a hint on this.

In short: the getaddrinfo() library function rates a private IPv4 address higher than the ULA IPv6 address when choosing the transport protocol for a new Internet connection if this add on to the RFC 3484 rules is compiled in. For this reason, you may want to change the @@ -70,7 +72,7 @@ ip6tables -t mangle -A POSTROUTING -o eth0 -s FD01:0203:0405::/48 -j SNPTV6 --to you cannot uncomment a single entry to overwrite the default. You need to uncomment all entries of a particular type for this. The “label” lines compare source addresses, the - “precedence” lines compare destination addresses.

Procedure 1. Change IPv6 Precedence

  1. Open the /etc/gai.conf file as root user, + “precedence” lines compare destination addresses.

    Procedure 1. Change IPv6 Precedence

    1. Open the /etc/gai.conf file as root user, e.g. by executing sudo nano /etc/gai.conf.

    2. Remove the leading hash character from the 8 lines starting with “#label”.

    3. Re-add the hash character to the line stating “#label -- cgit v1.2.3