summaryrefslogtreecommitdiffstats
path: root/doc/bird.sgml
blob: b3c2ea5db49f573a7e7c4c6f6de82b031b741480 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
<!doctype birddoc system>

<!--
	BIRD documentation

This documentation can have 4 forms: sgml (this is master copy), html,
ASCII text and dvi/postscript (generated from sgml using
sgmltools). You should always edit master copy.

This is slightly modified linuxdoc dtd.  Anything in <descrip> tags is considered definition of
configuration primitives, <cf> is fragment of configuration within normal text, <m> is
"meta" information within fragment of configuration - something in config which is not keyword.

    (set-fill-column 100)

    Copyright 1999,2000 Pavel Machek <pavel@ucw.cz>, distribute under GPL version 2 or later.

 -->

<book>

<title>BIRD User's Guide
<author>
Ondrej Filip <it/&lt;feela@network.cz&gt;/,
Pavel Machek <it/&lt;pavel@ucw.cz&gt;/,
Martin Mares <it/&lt;mj@ucw.cz&gt;/
</author>

<abstract>
This document contains user documentation for the BIRD Internet Routing Daemon project.
</abstract>

<!-- Table of contents -->
<toc>

<!-- Begin the document -->

<chapt>Introduction

<sect>What is BIRD

<p><label id="intro">
The name `BIRD' is actually an acronym standing for `BIRD Internet Routing Daemon'.
Let's take a closer look at the meaning of the name:

<p><em/BIRD/: Well, we think we have already explained that. It's an acronym standing
for `BIRD Internet Routing Daemon', you remember, don't you? :-)

<p><em/Internet Routing/: It's a program (well, a daemon, as you are going to discover in a moment)
which works as a dynamic router in an Internet type network (that is, in a network running either
the IPv4 or the IPv6 protocol). Routers are devices which forward packets between interconnected
networks in order to allow hosts not connected directly to the same local area network to
communicate with each other. They also communicate with the other routers in the Internet to discover
the topology of the network which allows them to find optimal (in terms of some metric) rules for
forwarding of packets (which will be called routes in the rest of this document) and to adapt themselves to the
changing conditions such as outages of network links, building of new connections and so on. Most of
these routers are costly dedicated devices running obscure firmware which is hard to configure and
not open to any changes (on the other hand, their special hardware design allows them to keep up with lots of high-speed network interfaces, better than general-purpose computer does). Fortunately, most operating systems of the UNIX family allow an ordinary 
computer to act as a router and forward packets belonging to the other hosts, but only according to
a statically configured table.

<p>A <em/Routing Daemon/ is in UNIX terminology a non-interactive program running on
background which does the dynamic part of Internet routing, that is it communicates
with the other routers, calculates routing tables and sends them to the OS kernel
which does the actual packet forwarding. There already exist other such routing daemons: routed (rip only), GateD<HTMLURL URL="http://www.gated.org/">
 (non free), Zebra<HTMLURL URL="http://www.zebra.org"> and mrtd<HTMLURL URL="FIXME">, but their capabilities are limited and
they are relatively hard to configure and maintain.

<p>BIRD is an Internet Routing Daemon designed to avoid all of these shortcomings,
to support all the routing technology used in the today's Internet or planned to be
used in near future and to have a clean extensible architecture allowing new routing
protocols to be incorporated easily. Among other features, BIRD supports:

<itemize>
	<item>both IPv4 and IPv6 protocols
	<item>multiple routing tables
	<item>the Border Gateway Protocol (BGPv4)
	<item>the Routing Interchange Protocol (RIPv2)
	<item>the Open Shortest Path First protocol (OSPFv2)
	<item>a virtual protocol for exchange of routes between different routing tables on a single host
	<item>a command-line interface allowing on-line control and inspection
		of status of the daemon
	<item>soft reconfiguration (no need to use complex online commands
		to change the configuration, just edit the configuration file
		and notify BIRD to re-read it and it will smoothly switch itself
		to the new configuration, not disturbing routing protocols
		unless they are affected by the configuration changes)
	<item>a powerful language for route filtering
</itemize>

<p>BIRD has been developed at the Faculty of Math and Physics, Charles University, Prague,
Czech Republic as a student project. It can be freely distributed under the terms of the GNU General
Public License.

<p>BIRD has been designed to work on all UNIX-like systems. It has been developed and
tested under Linux 2.0 to 2.4, but porting to other systems (even non-UNIX ones) should
be relatively easy due to its highly modular architecture.

<sect>Installing BIRD

<p>On a recent UNIX system with GNU development tools (GCC, binutils, m4, make) and Perl, installing BIRD should be as easy as:

<code>
        ./configure
        make
        make install
        vi /usr/local/etc/bird.conf
	bird
</code>

<p>You can use <tt>./configure --help</tt> to get a list of configure
options. The most important ones are:
<tt/--enable-ipv6/ which enables building of an IPv6 version of BIRD,
<tt/--with-protocols=/ to produce a slightly smaller BIRD executable by configuring out routing protocols you don't use, and
<tt/--prefix=/ to install BIRD to a place different from.
<file>/usr/local</file>.

<sect>Running BIRD

<p>You can pass several command-line options to bird:

<descrip>
	<tag>-c <m/config name/</tag>
	use given configuration file instead of <file>$prefix/etc/bird.conf</file>.

	<tag>-d</tag>
	enable debug messages and run bird in foreground.

	<tag>-D <m/filename of debug log/</tag>
	log debugging information to given file instead of stderr

	<tag>-s <m/name of communication socket/</tag>
	use given filename for a  socket for communications with the client, default is <file>$prefix/var/run/bird.ctl</file>.
</descrip>

<p>BIRD writes messages about its work to log files or syslog (according to config).

<chapt>About routing tables

<p>BIRD has one or more routing tables, which may or may not be
synchronized with kernel and which may or may not be synchronized with
each other (see the Pipe protocol). Each routing table contains list of
known routes. Each route consists of:

<itemize>
	<item>network prefix this route is for (consists of networkk address and number of bits forming the network part of the address)
	<item>preference of this route (taken from preference of
	protocol and possibly altered by filters)
	<item>IP address of router who told us about this route
	<item>IP address of router we should forward the packets to
	using this route
	<item>other attributes common to all routes
	<item>dynamic attributes defined by protocols which may or
	may not be present (typically protocol metrics)
</itemize>

Routing table maintains more than
one entry for a network, but at most one entry for one network and one
protocol. The entry with biggest preference is used for routing. If
there are more entries with the same preference and they are from the same
protocol, protocol decides (typically according to metrics). If not,
internal ordering is used to decide. You can
get list of route attributes in "Route attributes" section in
filters. 

<p>Protocols are connected to routing tables through filters. Routes
that come from other routers go to the protocol, it then passes them to
filters, if import filter accepts route, it gets to main routing
table. It is then broadcasted to all other protocols (filtered through
their export filters), which typically send it to other routers.

Filters can alter routes passed between routing tables and
protocols.

<chapt>Configuration

<sect>Introduction

<!-- fixme: add default values to all places? Where do I learn them? --> 

<p>BIRD is configured using a text configuration file. Upon startup, BIRD reads <file>$prefix/bird.conf</file> (unless the
<tt/-c/ command line option is given). Configuration may be changed on user's request: if you modify
config file and then signal BIRD with SIGHUP, it will adjust to the new
config. Then there's the client,
which allows you to talk with BIRD in an extensive way. (Of course you can tell BIRD to reconfigure from BIRDC, you can also tell it to shut down, dump various info etc.).

<p>In the config, everything on a line after <cf/#/ or inside <cf>/*
*/</cf> is a comment, whitespace characters are treated as a single space. If there's a variable number of options, they are grouped using
the <cf/{ }/ brackets. Each option is terminated by a <cf/;/. Configuration
is case sensitive.

<p>Here is an example of a simple config file. It enables
synchronization of routing tables with OS kernel, scans for 
new network interfaces every 10 seconds and runs RIP on all network interfaces found.


<code>
protocol kernel {
	persist;		# Don't remove routes on BIRD shutdown
	scan time 20;		# Scan kernel routing table every 20 seconds
	export all;		# Default is export none
}

protocol device {
	scan time 10;		# Scan interfaces every 10 seconds
}

protocol rip {
	export all;
	import all;
}
</code>


<sect>Global options

<p><descrip>
	<tag>log "<m/filename/"|syslog|stderr all|{ <m/list of classes/ }</tag> 
	Set logging of messages having the given (either <cf/all/ or <cf/{
	error, trace }/ etc.) into selected destination. Classes are:
	<cf/info/, <cf/warning/, <cf/error/ and <cf/fatal/ for messages about local problems
	<cf/debug/ for debugging messages, 
	<cf/trace/ when you want to know what happens in the network, 
	<cf/remote/ for messages about misbehavior of remote machines, 
	<cf/auth/ about authentication failures,
	<cf/bug/ for internal BIRD bugs. You may specify more than one <cf/log/ line to estabilish logging to multiple
	destinations.

	<!--fixme: mj says explain-->
				  
	<tag>debug protocols all|off|{ states, routes, filters, interfaces, events, packets }</tag>
	Set global default of protocol debugging options.

	<tag>filter <m/name local variables/{ <m/commands/ }</tag> Define a filter. You can learn more about filters
	in the following chapter.

	<tag>function <m/name (parameters) local variables/ { <m/commands/ }</tag> Define a function. You can learn more
	about functions in the following chapter.
 
	<tag>protocol rip|ospf|bgp|... <m/[name]/ { <m>protocol options</m> }</tag> Define a protocol
	instance called <cf><m/name/</cf> (or with a name like "rip5" generated automatically, if you don't specify <cf><m/name/</cf>). You can learn more
	about configuring protocols in their own chapters. You can run more than one instance of
	most protocols (like RIP or BGP).

	<tag>define <m/constant/ = (<m/expression/)|<m/number/|<m/IP address/</tag> Define a constant. You can use it later in every place
	you could use a simple integer or IP address.

	<tag>router id <m/IPv4 address/</tag> Set BIRD's router ID. It's a world-wide unique identification of your router, usually one of router's IPv4 addresses.

	<tag>table <m/name/</tag> Create a new routing table. The default
	routing table is created implicitly, other routing tables have
	to be added by this command.

	<tag>eval <m/expr/</tag> Evaluates given filter expression. It
	is used by us for testing filters.
</descrip>

<sect>Protocol options

<p>Each routing protocol has its own set of options (see the corresponding sections). These options are common to all protocols:

<descrip>
	<tag>preference <m/expr/</tag> Sets the preference of routes generated by this protocol.

	<tag>disabled</tag> Disables the protocol. You can change the disable/enable status from the command
	line interface without needing to touch the configuration. Disabled protocol is not activated.

	<tag>debug <m/setting/</tag> Similar to global <cf/debug/ setting, except that it only
	affects one protocol. Only messages in selected debugging categories will be written to the
	logs.

	<tag>import { <m/filter commands/ } | <m/name/ | all | none</tag> Specify a filter to be used for filtering routes comming from protocol tothe routing table. Default: <cf/all/. <cf/all/ is shorthand for <cf/{ accept; }/ and <cf/none/ is shorthand for <cf/{ reject; }/.

	<tag>export <m/filter/</tag> This is similar to <cf>import</cf> keyword, except that it
	works in direction from the routing table to the protocol. Default: <cf/none/

	<tag>table <m/name/</tag> Connect this protocol to a non-default routing table.
</descrip>

<p>There are several options that give sense only with certain protocols:

<descrip>
	<tag>passwords { password "<m/password/" from <m/time/ to <m/time/ passive <m/time/ id
	<m/num/ [...] }</tag> Specifies passwords to be used with this protocol. <cf>Passive <m/time/</cf> is
	time from which the password is not used for sending, but it is recognized on reception. <cf/id/ is password id, as needed by
	certain protocols.

	<tag>interface "<m/mask/"|<m/prefix/ [ { <m/option/ ; [ ... ] } ]</tag> Specifies which
	interfaces this protocol is active on, and allows you to set options on
	per-interface basis. Mask is specified in shell-like patterns, thus <cf>interface
	"*" { mode broadcast; };</cf> will start the protocol on all interfaces with <cf>mode
	broadcast;</cf> option. If first character of mask is <cf/-/, such interfaces are
	excluded. Masks are parsed left-to-right, thus <cf/interface "-eth*", "*";/ means all but
	the ethernets.
						  
</descrip>

<sect>Client

<p>You can use the command-line client <file>birdc</file> to talk with
a running BIRD. Communication is done using <file/bird.ctl/ unix domain
socket (unless changed with the <tt/-s/ option given to both the server and
the client). The client can do simple actions such as enabling/disabling
protocols, telling BIRD to show various information, telling it to
show routing table filtered by any filter, or telling bird to
reconfigure. Press <tt/?/ at any time to get online help. Option
<tt/-v/ can be passed to the client, telling it to dump numeric return
codes. You do not necessarily need to use BIRDC to talk to BIRD, your
own application could do that, too -- format of communication between
BIRD and BIRDC is stable (see programmer's documentation).


<chapt>Filters

<sect>Introduction

<p>BIRD contains a rather simple programming language. (No, it can't yet read mail :-). There are
two objects in this language: filters and functions. Filters are called by BIRD core when a route is
being passed between protocola and routing tables. Filter language contains control structures such
as if's and switches, but it allows no loops. Filters are
interpreted. An example of a filter using many features can be found in <file>filter/test.conf</file>. 

<p>Filter gets the route, looks at its attributes and
modifies some of them if it wishes. At the end, it decides whether to
pass the changed route through (using <cf/accept/) or whether to <cf/reject/ given route. A simple filter looks
like this:

<code>
filter not_too_far
int var;
{
	if defined( rip_metric ) then
		var = rip_metric;
	else {
		var = 1;
		rip_metric = 1;
	}
	if rip_metric &gt; 10 then
		reject "RIP metric is too big";
	else
		accept "ok";
}
</code>

<p>As you can see, a filter has a header, a list of local variables, and a body. The header consists of
the <cf/filter/ keyword, followed by a (unique) name of filter. List of local variables consists of
pairs <cf><M>type name</M>;</cf>, where each pair defines one local variable. Body consists of
<cf> { <M>statements</M> }</cf>. Each <m/statement/ is terminated by <cf/;/. You can group
several statements into one by using braces (<cf>{ <M>statements</M> }</cf>), that is useful if
you want to make bigger block of code conditional.

<p>BIRD supports functions, so that you don't have to repeat same blocks of code over and
over. Functions can have zero or more parameters and they can have local variables. Recursion is not allowed. They
look like this:

<code>
function name ()
int local_variable;
{
	local_variable = 5;
}

function with_parameters (int parameter)
{
	print parameter;
}
</code>

<p>Unlike in C, variables are declared after function line but before the first {. You can't declare
variables in nested blocks. Functions are called like in C: <cf>name();
with_parameters(5);</cf>. Function may return value using the <cf>return <m/[expr]/</cf>
command. Returning a value exits from current function (this is similar to C).

<p>Filters are declared in a way similar to functions except they can't have explicit
parameters. They get route table entry as an implicit parameter, it is also passed automatically 
to any functions called. The filter must terminate with either
<cf/accept/ or <cf/reject/ statement. If there's runtime error in filter, the route
is rejected. 

<p>A nice trick to debug filters is to use <cf>show route filter
<m/name/</cf> from the command line client. An example session might look
like:

<code>
pavel@bug:~/bird$ ./birdc -s bird.ctl
BIRD 0.0.0 ready.
bird> show route
10.0.0.0/8         dev eth0 [direct1 23:21] (240)
195.113.30.2/32    dev tunl1 [direct1 23:21] (240)
127.0.0.0/8        dev lo [direct1 23:21] (240)
bird> show route ?
show route [<prefix>] [table <t>] [filter <f>] [all] [primary] [(import|protocol) <p>]...
bird> show route filter { if 127.0.0.5 ~ net then accept; }
127.0.0.0/8        dev lo [direct1 23:21] (240)
bird>
</code>

<sect>Data types

<p>Each variable and each value has certain type. Booleans, integers and enums are
incompatible with each other (that is to prevent you from shooting in the foot).

<descrip>
	<tag/bool/ This is a boolean type, it can have only two values, <cf/true/ and
	  <cf/false/. Boolean is not compatible with integer and is the only type you can use in if
	  statements.

	<tag/int/ This is a general integer type, you can expect it to store signed values from -2000000000
	  to +2000000000. Overflows are not checked. You can use <cf/0x1234/ syntax to write hexadecimal values.

	<tag/pair/ This is a pair of two short integers. Each component can have values from 0 to
	  65535. Literals of this type is written as <cf/(1234,5678)/.

	<tag/string/ This is a string of characters. There are no ways to modify strings in
	  filters. You can pass them between functions, assign them to variables of type <cf/string/, print
	  such variables, but you can't concatenate two strings. String literals
	  are written as <cf/"This is a string constant"/.

	<tag/ip/ This type can hold a single IP address. Depending on the compile-time configuration of BIRD you are using, it
	  is either an IPv4 or IPv6 address. IPv4 addresses are written (as you would expect) as
	  <cf/1.2.3.4/. You can apply special operator <cf>.mask(<M>num</M>)</cf>
	  on values of type ip. It masks out all but first <cf><M>num</M></cf> bits from ip
	  address. So <cf/1.2.3.4.mask(8) = 1.0.0.0/ is true. <!-- FIXME: IPv6? -->

	<tag/prefix/ This type can hold a network prefix consisting of IP address and prefix length. Prefix literals are written as
	  <cf><M>ipaddress</M>/<M>pxlen</M></cf>, or
	  <cf><m>ipaddress</m>/<m>netmask</m></cf> There are two special
	  operators on prefix:
	  <cf/.ip/, which separates ip address from the pair, and <cf/.len/, which separates prefix
	  len from the pair. So <cf>1.2.0.0/16.pxlen = 16</cf> is true.

	<tag/int|ip|prefix|pair|enum set/
	  Filters recognize four types of sets. Sets are similar to strings: you can pass them around
	  but you can't modify them. Literals of type <cf>set int</cf> look like <cf>
	  [ 1, 2, 5..7 ]</cf>. As you can see, both simple values and ranges are permitted in
	  sets. Sets of prefixes are special: you can specify which prefix lengths should match them by
	  using <cf>[ 1.0.0.0/8+, 2.0.0.0/8-, 3.0.0.0/8{5,6} ]</cf>. <cf>3.0.0.0/8{5,6}</cf> matches
	  prefixes <cf/3.X.X.X/, whose prefix length is 5 to 6. <cf>3.0.0.0/8+</cf> is shorthand for <cf>3.0.0.0/{0,8}</cf>,
	  <cf>3.0.0.0/8-</cf> is shorthand for <cf>3.0.0.0/{0,7}</cf>. For example,
	  <cf>1.2.0.0/16 ~ [ 1.0.0.0/8{ 15 , 17 } ]</cf> is true, but
	  <cf>1.0.0.0/8 ~ [ 1.0.0.0/8- ]</cf> is false. <!-- fixme: use variables instead of examples -->

	<tag/enum/
	  Enumeration types are fixed in BIRD - you can't define your own
	  variables of enumeration type, but some route attributes are of enumeration
	  type. Enumeration types are incompatible with each other.

	<tag/bgppath/
	  BGP path is a list of autonomous system numbers. You can't write literals of this type.

	<tag/bgpmask/ 
	  BGP mask is a mask used for matching BGP paths
	  (using <cf>path &tilde; /2 3 5 ?/</cf> syntax). Matching is
	  done using shell-like patterns: <cf/?/ means
	  "any number of any autonomous systems". Pattern for single
	  unknown autonomous system is not supported. (We
	  did not want to use * because then it becomes too easy to
	  write <cf>/*</cf> which is start of comment.) For example,
	  <tt>/4 3 2 1/ ~ /? 4 3 ?/</tt> is true, but 
	  <tt>/4 3 2 1/ ~ /? 4 5 ?/</tt> is false. <!-- fixme: formulate better -->

	<tag/clist/ 
	  Community list is similar to set of pairs,
	  except that unlike other sets, it can be modified.
	  There exist no literals of this type.

</descrip>

<sect>Operators

<!-- FIXME: Make it table -->

<p>The filter language supports common integer operators <cf>(+,-,*,/)</cf>, parentheses <cf/(a*(b+c))/, comparison
<cf/(a=b, a!=b, a&lt;b, a&gt;=b)/. Special operators include <cf/&tilde;/ for "in" operation. In operation can be
used on element and set of that elements, or on ip and prefix, or on
prefix and prefix or on bgppath and bgpmask or on pair and clist. Its result
is true if element is in given set or if ip address is inside given prefix. Logical operations include unary not (<cf/!/), and (<cf/&&/) and or (<cf/||/).

<sect>Control structures

<p>Filters support two control structures: conditions and case switches. 

<!-- fixme: say explicitly what if and case does -->

<p>Syntax of condition is <cf>if
<M>boolean expression</M> then <M>command</M>; else <M>command</M>;</cf> and you can use <cf>{
<M>command_1</M>; <M>command_2</M>; <M>...</M> }</cf> instead of one or both commands. <cf>else</cf>
clause may be omitted.

<p><cf>case</cf> is similar to case from Pascal. Syntax is <cf>case <m/expr/ { else |
<m/num_or_prefix [ .. num_or_prefix]/: <m/statement/ ; [ ... ] }</cf>. Expression after
<cf>case</cf> can be of any type that can be on the left side of the &tilde; operator, and anything that could
be a member of a set is allowed before <cf/:/. Multiple commands are allowed without <cf/{}/ grouping
and break is implicit before each case. If argument
matches neither of <cf/:/ clauses, <cf/else:/ clause is used.

<p>Here is example that uses <cf/if/ and <cf/case/ structures:

<code>
case arg1 {
	2: print "two"; print "I can do more commands without {}";
	3 .. 5: print "three to five";
	else: print "something else";
}

if 1234 = i then printn "."; else { 
  print "not 1234"; 
  print "You need {} around multiple commands"; 
}
</code>

<sect>Route attributes

<p>An filter is implicitly passed route, and it can access its
attributes just like it accesses variables. Attempt to access undefined
attribute result in a runtime error; you can check if an attribute is
defined using the <cf>defined( <m>attribute</m> )</cf> operator.

<!-- fixme: say which are read-only -->

<descrip>
	<tag><m/prefix/ net</tag>
	Network the route is talking about. (See the section about routing tables.)

	<tag><m/enum/ scope</tag>
	Address scope of the network (<cf/SCOPE_HOST/ for addresses local to this host, <cf/SCOPE_LINK for those specific for a physical link, ... <!-- FIXME -->)

	<tag><m/int/ preference</tag>
	Preference of the route. (See section about routing tables.)

	<tag><m/ip/ from</tag>
	The router which the route has originated from.
	
	<tag><m/ip/ gw</tag>
	Next hop packets routed using this route should be forwarded to.

	<tag><m/enum/ source</tag>
	what protocol has told me about this route. Possible values: <cf/RTS_RIP/ or <cf/RTS_OSPF_EXT/ <!-- fixme -->.

	<tag><m/enum/ cast</tag>
	Route type (<cf/RTC_UNICAST/ for normal routes, ... <!-- FIXME -->)

	<tag><m/enum/ dest</tag>
	Type of destination the packets should be sent to (<cf/RTD_ROUTER/ for forwarding to a neighboring router, ...)
</descrip>

<p>There also exist some protocol-specific attributes, which are described in protocol sections.

<sect>Statements

<p>The following statements are available:

<descrip>
	<tag><m/variable/ = <m/expr/</tag> Set variable to a given value.

	<tag>accept|reject [ <m/expr/ ]</tag> Accept or reject the route, possibly printing <cf><m>expr</m></cf>.

	<tag>return <m/expr/</tag> Return <cf><m>expr</m></cf> from function, the function ends at this point.

	<tag>print|printn <m/expr/ [<m/, expr.../]</tag>
	Prints given expressions; useful mainly while debugging
	filters. The <cf/printn/ variant does not terminate the line.

	<tag>quitbird</tag>
	Terminates BIRD. Useful when debugging filter interpreter.
</descrip>

<chapt>Protocols

<sect>BGP

<p>The Border Gateway Protocol is the routing protocol used for backbone
level routing in the today's Internet. Contrary to other protocols, its convergence
doesn't rely on all routers following the same rules for route selection,
making it possible to implement any routing policy at any router in the
network, the only restriction being that if a router advertises a route,
it must accept and forward packets according to it.

<p>BGP works in terms of autonomous systems (often abbreviated as AS). Each
AS is a part of the network with common management and common routing policy.
Routers within each AS usually communicate using either a interior routing
protocol (such as OSPF or RIP) or an interior variant of BGP (called iBGP).
Boundary routers at the border of the AS communicate with their peers
in the neighboring AS'es via exterior BGP (eBGP).

<p>Each BGP router sends to its neighbors updates of the parts of its
routing table it wishes to export, along with complete path information
(a list of AS'es the packet will travel through if it uses that particular
route) in order to avoid routing loops.

<p>BIRD supports all requirements of the BGP4 standard as defined in
RFC 1771<htmlurl url="ftp://ftp.rfc-editor.org/in-notes/rfc1771.txt">
including several enhancements from the
latest draft<htmlurl url="ftp://ftp.rfc-editor.org/internet-drafts/draft-ietf-idr-bgp4-09.txt">.
It also supports the community attributes as per
RFC 1997<htmlurl url="ftp://ftp.rfc-editor.org/in-notes/rfc1997.txt">,
capability negotiation defined in
RFC 2842<htmlurl url="ftp://ftp.rfc-editor.org/in-notes/rfc2842.txt">,
For IPv6, it uses the standard multiprotocol extensions defined in
RFC 2283<htmlurl url="ftp://ftp.rfc-editor.org/in-notes/rfc2283.txt">
including changes described in the
latest draft <htmlurl url="ftp://ftp.rfc-editor.org/internet-drafts/draft-ietf-idr-bgp4-multiprotocol-v2-05.txt">
and applied to IPv6 according to
RFC 2545<htmlurl url="ftp://ftp.rfc-editor.org/in-notes/rfc2545.txt">.

<sect1>Route selection rules

<p>BGP doesn't have any simple metric, so the rules for selection of an optimal
route among multiple BGP routes with the same preference are a bit more complex
and are implemented according to the following algorithm. First it uses the first
rule, if there are more "best" routes, then it uses the second rule to choose
among them and so on.

<itemize>
	<item>Prefer route with the highest local preference attribute.
	<item>Prefer route with the shortest AS path.
	<item>Prefer IGP origin over EGP and EGP over incomplete.
	<item>Prefer the lowest value of the Multiple Exit Discriminator.
	<item>Prefer internal routes over external routes.
	<item>Prefer route with the lowest value of router ID of the
	advertising router.
</itemize>

<sect1>Configuration

<p>Each instance of the BGP corresponds to one neighboring router.
This allows to set routing policy and all other parameters differently
for each neighbor using the following protocol parameters:

<descrip>
	<tag>local as <m/number/</tag> Define which AS we are part of. (Note that
	contrary to other IP routers, BIRD is able to act as a router located
	in multiple AS'es simultaneously, but in such cases you need to tweak
	the BGP paths manually in the filters to get consistent behavior.)
	This parameter is mandatory.
	<tag>neighbor <m/ip/ as <m/number/</tag> Define neighboring router
	this instance will be talking to and what AS it's located in. Unless
	you use the <cf/multihop/ clause, it must be directly connected to one
	of your router's interfaces. In case the neighbor is in the same AS
	as we are, we automatically switch to iBGP. This parameter is mandatory.
	<tag>multihop <m/number/ via <m/ip/</tag> Configure multihop BGP to a
	neighbor which is connected at most <m/number/ hops far and to which
	we should route via our direct neighbor with address <m/ip/.
	Default: switched off.
	<tag>next hop self</tag> Avoid calculation of the Next Hop attribute
	and always advertise our own source address (see below) as a next hop.
	This needs to be used only
	occasionally to circumvent misconfigurations of other routers.
	Default: disabled.
	<tag>source address <m/ip/</tag> Define local address we should use
	for next hop calculation. Default: the address of the local end
	of the interface our neighbor is connected to.
	<tag>disable after error <m/switch/</tag> When an error is encountered (either
	locally or by the other side), disable the instance automatically
	and wait for an administrator to solve the problem manually. Default: off.
	<tag>hold time <m/number/</tag> Time in seconds to wait for a keepalive
	message from the other side before considering the connection stale.
	Default: depends on agreement with the neighboring router, we prefer
	240 seconds if the other side is willing to accept it.
	<tag>startup hold time <m/number/</tag> Value of the hold timer used
	before the routers have a chance to exchange OPEN messages and agree
	on the real value. Default: 240 seconds.
	<tag>keepalive time <m/number/</tag> Delay in seconds between sending
	of two consecutive keepalive messages. Default: One third of the hold time.
	<tag>connect retry time <m/number/</tag> Time in seconds to wait before
	retrying a failed connect attempt. Default: 120 seconds.
	<tag>start delay time <m/number/</tag> Delay in seconds between protocol
	startup and first attempt to connect. Default: 5 seconds.
	<tag>error wait time <m/number/, <m/number/</tag> Minimum and maximum delay in seconds between protocol
	failure (either local or reported by the peer) and automatic startup.
	Doesn't apply when <cf/disable after error/ is configured. If consecutive
	errors happen, the delay is increased exponentially until it reaches the maximum. Default: 60, 300.
	<tag>error forget time <m/number/</tag> Maximum time in seconds between two protocol
	failures to treat them as a error sequence which makes the <cf/error wait time/
	increase exponentially. Default: 300 seconds.
	<tag>path metric <m/switch/</tag> Enable comparison of path lengths
	when deciding which BGP route is the best one. Default: on.
	<tag>default bgp_med <m/number/</tag> Value of the Multiple Exit
	Discriminator to be used during route selection when the MED attribute
	is missing. Default: infinite.
	<tag>default bgp_local_pref <m/number/</tag> Value of the Local Preference
	to be used during route selection when the Local Preference attribute
	is missing. Default: 0.
</descrip>

<sect1>Attributes

<p>BGP defines several route attributes. Some of them (those marked with `I' in the
table below) are available on internal BGP connections only, some of them (marked
with `O') are optional.

<descrip>
	<tag>bgppath <cf/bgp_path/</tag> Sequence of AS numbers describing the AS path
	the packet will travel through when forwarded according to this route. On
	internal BGP connections it doesn't contain the number of the local AS.
	<tag>int <cf/bgp_local_pref/ [I]</tag> Local preference value used for
	selection among multiple BGP routes (see the selection rules above). It's
	used as an additional metric which is propagated through the whole local AS.
	<tag>int <cf/bgp_med/ [IO]</tag> The Multiple Exit Discriminator of the route
	is an optional attribute which is often used within the local AS to
	reflect interior distances to various boundary routers. See the route selection
	rules above for exact semantics.
	<tag>enum <cf/bgp_origin/</tag> Origin of the route: either <cf/ORIGIN_IGP/,
	if the route has originated in interior routing protocol of an AS or
	<cf/ORIGIN_EGP/, if it's been imported from the <tt>EGP</tt> protocol
	(nowadays it seems to be obsolete) or <cf/ORIGIN_INCOMPLETE/, if the origin
	is unknown.
	<tag>ip <cf/bgp_next_hop/</tag> Next hop to be used for forwarding of packets
	to this destination. On internal BGP connections, it's an address of the
	originating router if it's inside the local AS or a boundary router the
	packet will leave the AS through if it's an exterior route, so each BGP
	speaker within the AS has a chance to use the shortest interior path
	possible to this point.
	<tag>void <cf/bgp_atomic_aggr/ [O]</tag> This is an optional attribute
	which carries no value, but which sole presence indicates that the route
	has been aggregated from multiple routes by some AS on the path from
	the originator.
<!-- we don't handle aggregators right since they are of a very obscure type
	<tag>bgp_aggregator</tag>
-->
	<tag>clist <cf/bgp_community/ [O]</tag> List of community values associated
	with the route. Each such value is a pair (represented as a <cf/pair/ data
	type inside the filters) of 16-bit integers, the first of them containing a number of the AS which defines
	the community and the second one is a per-AS identifier. There are lots
	of uses of the community mechanism, but generally they are used to carry
	policy information like "don't export to USA peers". As each AS can define
	its own routing policy, it also has a complete freedom about which community
	attributes it defines and what their semantics will be.
</descrip>

<sect1>Example

<p><code>
protocol bgp {
	local as 65000;				# Use a private AS number
	neighbor 62.168.0.130 as 5588;		# Our neighbor
	multihop 20 via 62.168.0.13;		# Which is connected indirectly
	export filter {				# We use non-trivial export rules
		if source = RTS_STATIC then {	# Export only static routes
		        # Assign our community
			bgp_community.add((65000,5678));
			# Artificially increase path length
			# by prepending local AS number twice
			if bgp_path ~ / 65000 / then	  
				bgp_path.prepend(65000);  
			accept;
		}
		reject;
	};
	import all;
	source address 62.168.0.1;		# Use non-standard source address
}
</code>

<sect>Device

<p>The Device protocol is not a real routing protocol as it doesn't generate
any routes and only serves as a module for getting information about network
interfaces from the kernel.

<p>Except for very unusual circumstances, you probably should include
this protocol in the configuration since almost all other protocol
require network interfaces to be defined in order to work.

<p>The only configurable thing is interface scan time:

<p><descrip>
	<tag>scan time <m/number/</tag> Time in seconds between two scans
	of the network interface list. On systems where we are notified about
	interface status changes asynchronously (such as newer versions of
	Linux), we need to scan the list only to avoid confusion by lost
	notifications, so the default time is set to a large value.
</descrip>

<p>As the Device protocol doesn't generate any routes, it cannot have
any attributes. Example configuration looks really simple:

<p><code>
protocol device {
	scan time 10;		# Scan the interfaces often
}
</code>

<sect>Direct

<p>The Direct protocol is a simple generator of device routes for all the
directly connected networks according to the list of interfaces provided
by the kernel via the Device protocol.

<p>It's highly recommended to include this protocol in your configuration
unless you want to use BIRD as a route server or a route reflector, that is
on a machine which doesn't forward packets and only participates in
distribution of routing information.

<p>Only configurable thing about direct is what interfaces it watches:

<p><descrip>
	<tag>interface <m/pattern [, ...]/</tag> By default, the Direct
	protocol will generate device routes for all the interfaces
	available. If you want to restrict it to some subset of interfaces
	(for example if you're using multiple routing tables for policy
	routing and some of the policy domains don't contain all interfaces),
	just use this clause.
</descrip>

<p>Direct device routes don't contain any specific attributes.

<p>Example config might look like this:

<p><code>
protocol direct {
	interface "-arc*", "*";		# Exclude the ARCnets
}
</code>

<sect>Kernel

<p>The Kernel protocol is not a real routing protocol. Instead of communicating
with other routers in the network, it performs synchronization of BIRD's routing
tables with OS kernel. Basically, it sends all routing table updates to the kernel
and from time to time it scans the kernel tables to see whether some routes have
disappeared (for example due to unnoticed up/down transition of an interface)
or whether an `alien' route has been added by someone else (depending on the
<cf/learn/ switch, such routes are either deleted or we accept them to our
table).

<p>If your OS supports only a single routing table, you can configure only one
instance of the Kernel protocol. If it supports multiple tables (in order to
allow policy routing), you can run as many instances as you want, but each of
them must be connected to a different BIRD routing table and to a different
kernel table.

<sect1>Configuration

<p><descrip>
	<tag>persist <m/switch/</tag> Tell BIRD to leave all its routes in the
	routing tables when it exits (instead of cleaning them up).
	<tag>scan time <m/number/</tag> Time in seconds between two scans of the
	kernel routing table.
	<tag>learn <m/switch/</tag> Enable learning of routes added to the kernel
	routing tables by other routing daemons or by the system administrator.
	This is possible only on systems which support identification of route
	authorship.
	<tag>kernel table <m/number/</tag> Select which kernel table should
	this particular instance of the Kernel protocol work with. Available
	only on systems supporting multiple routing tables.
</descrip>

<p>A simple configuration can look this way:

<p><code>
protocol kernel {
	import all;
	export all;
}
</code>

<p>Or for a system with two routing tables:

<p><code>
protocol kernel {		# Primary routing table
	learn;			# Learn alien routes from the kernel
	persist;		# Don't remove routes on bird shutdown
	scan time 10;		# Scan kernel routing table every 10 seconds
	import all;
	export all;
}

protocol kernel {		# Secondary routing table
	table auxtable;
	kernel table 100;
	export all;
}
</code>

<p>The Kernel protocol doesn't define any route attributes.

<sect>OSPF

<sect1>Introduction

<p>Open Shortest Path First (OSPF) is quite complex interior gateway
protocol.  Today's version for IPv4 is 2 and it's defined in RFC 2328<htmlurl
url="ftp://ftp.rfc-editor.org/in-notes/rfc2328.txt">. It's based on
link-state of SPF technology. Each router maintains a database
describing the Autonomous System's topology. Each participating router has
has an identical database and all routers run the exact same algorithm
calculatin shortest path tree with themselves as roots, in parallel.
OSPF chooses the least cost path as the best path. In OSPF, the
Autonomous System can be splitted into more areas. Topology
of such area is hidden to the rest of the Autonomous System. This enables
a reduction in routing traffic as well as protection other areas from bad
routing data. Unfortunatelly multiple OSPF areas are not fully supported
in this version of BIRD. Another very important feature of OSPF is that
it can keep routing information from other protocols (like static or BGP)
in it's link-state database as external routes. Each external route can
be tagged by the advertising router, enabling the passing of additional
information between routers on the boundary of the Autonomous System.

<p>OSPF quickly detects topological changes in the Autonomous System (such
as router interface failures) and calculates new loop-free routes after a
period of convergence. This period of convergence is short and involves
a minimum of routing traffic.

<p>Each router joined in OSPF periodically sends hello messages out
all its interfaces. This allows neighbors to be discovered dynamically.
Then the neighbors exchange theirs parts of database. And keep it
identical flooding updates. Flooding proces is reliable and ensures
that each routes detects the change.

<sect1>Configuration

<p>

<code>
protocol ospf <name> {
	rfc1583compat bool;
	area <id> {
		stub <bool>;
		tick <num>;
		interface <interface>
		{
			cost <num>;
			hello <num>;
			retransmit <num>;
			priority <num>;
			wait <num>;
			dead count <num>;
			type [broadcast|nonbroadcast|pointopoint];
			authetication [none|simple];
			password "<text>";
			neighbors {
				<ip>;
			};
		};
	};
}
</code>

<descrip>
	<tag>rfc1583compat <M>bool</M></tag>
	 This option can disable or enable compatibility of routing table
	 calculation with RFC 1583<htmlurl
	 url="ftp://ftp.rfc-editor.org/in-notes/rfc1583.txt">. Default
	 value is no.
	
	<tag>area <M>id</M></tag>
	 This specifies area id of configured OSPF area. It can be written
	 as a number or as an IPv4 number. The most important area is
	 the backbone (area id 0) to which every other area must be connected.

	<tag>stub <M>bool</M></tag>
	 No external routes are flooded into stub area. Default value is no.

	<tag>tick <M>num</M></tag>
	 The routing table calculation is not processed when any single
	 change comes. To lower the CPU utilization it's processed late
	 in periodical interval. The default value is 7.

	<tag>interface <M>interface</M></tag>
	 This mean that specified interface (or interface pattern) belongs
	 to actual area.

	<tag>cost <M>num</M></tag>
	 Specifies output cost of interface. Default value is 10.

	<tag>hello <M>num</M></tag>
	 Specifies interval between sending hello messages. Beware, all
	 router on the same network has to have the same hello interval.
	 Default value is 10.

	<tag>retransmit <M>num</M></tag>
	 Specifies interval between retransmiting unacknoledged update.
	 Default value is 5.

        <tag>priority <M>num</M></tag>
	 On every multiple access network (like e.g ethernet) Designed
	 and Backup Designed router is elected. These routers have some
	 special functions in flooding process. Higher priority rices
	 preferences in elections. Routers with priority 0 are not
	 eligible. Default value is 1.

	<tag>wait <M>num</M></tag>
	 After start, router waits specified interval between starting
	 election and building adjacency. Default value is 40.
	 
	<tag>dead count <M>num</M></tag>
	 When router does not receive any message from neighbor in
	 <dead count>*<hello> seconds, it will declare neighbor down.

	<tag>type <M>broadcast</M><tag>
	 BIRD detects a type of connected network. However, sometimes is
	 necessary to change it. On broadcast networks are flooding
	 and hello messages sent using multicasting. (Single
	 packet to all neighbors.)

	<tag>type <M>nonbroadcast</M></tag>
	 On nonbroadcast network are packets sent to each neighbor
	 separately because of lack of multicast messages.

	<tag>type <M>pointopoint</M></tag>
	 Pointopoint network connects just 2 routers together. No election
	 is provided there, this reduces a number of sent messages.

	<tag>authetication <M>none</M></tag>
	 No passwords are sent in OSPF's packets. This is default value.

	<tag>authetication <M>simple</M></tag>
	 In every packet is sent an 8 bytes long password. Received packets
	 without this password are ignored. This autentication mechanism is
	 very weak.

	<tag>password <M>text</M></tag>
	 An 8 bytes long password used for authentication.

	<tag>neighbors</tag>
	 A set of neighbors to which hello messages on nonbroadcast networks
	 are sent.
</descrip>

<sect1>Attributes

<p>OSPF defines 3 route attributes. Each internal route has a metric. External
routes uses metric type 1 or metric type 2. Metric type one is comparable
with internal metric. Metric type 2 is always longer then metric type 1
or internal metric. Each external route can also carry a tag. Tag is
32 bits long number and it's used for exporting routes to other protocols
in link-state it has no funtion.

<sect1>Example

<p>

<code>
protocol ospf MyOSPF {
	area 0.0.0.0 {
		tick 8;
		interface "eth*" {
			cost 11;
			hello 15;
			priority 100;
			retransmit 7;
			authentication simple;
			password "aaa";
		};
		interface "ppp*" {
			cost 100;
		};
	};
	area 120 {
		stub yes;
		interface "-arc0" , "arc*" {
			type nonbroadcast;
			authentication none;
			wait 50;
			dead count 6;
			neighbors {
				192.168.120.1;
				192.168.120.2;
				192.168.120.10;
			};
		};
	};
}
</code>

<sect>Pipe

<sect1>Introduction

<p>The Pipe protocol serves as a link between two routing tables, allowing routes to be
passed from a table declared as primary (i.e., the one the pipe is connected using the
<cf/table/ configuration keyword) to the secondary one (declared using <cf/peer table/)
and vice versa, depending on what's allowed by the filters. Export filters control export
of routes from the primary table to the secondary one, import filters control the opposite
direction.

<p>The primary use of multiple routing tables and the pipe protocol is for policy routing,
where handling of a single packet doesn't depend only on its destination address, but also
on its source address, source interface, protocol type and other similar parameters.
In many systems (Linux 2.2 being a good example) the kernel allows to enforce routing policies
by defining routing rules which choose one of several routing tables to be used for a packet
according to its parameters. Setting of these rules is outside the scope of BIRD's work
(you can use the <tt/ip/ command), but you can create several routing tables in BIRD,
connect them to the kernel ones, use filters to control which routes appear in which tables
and also you can employ the Pipe protocol to export a selected subset of one table in
another one.

<sect1>Configuration

<p><descrip>
	<tag>peer table <m/table/</tag> Define secondary routing table to connect to. The
	primary one is selected by the <cf/table/ keyword.
</descrip>

<sect1>Attributes

<p>The Pipe protocol doesn't define any route attributes.

<sect1>Example

<p>Let's consider a router which serves as a boundary router of two different autonomous
systems, each of them connected to a subset of interfaces of the router, having its own
exterior connectivity and wishing to use the other AS as a backup connectivity in case
of outage of its own exterior line.

<p>Probably the simplest solution to this situation is to use two routing tables (we'll
call them <cf/as1/ and <cf/as2/) and set up kernel routing rules, so that packets having
arrived from interfaces belonging to the first AS will be routed according to <cf/as1/
and similarly for the second AS. Thus we have split our router to two logical routers,
each one acting on its own routing table, having its own routing protocols on its own
interfaces. In order to use the other AS's routes for backup purposes, we can pass
the routes between the tables through a Pipe protocol while decreasing their preferences
and correcting their BGP paths to reflect AS boundary crossing.

<code>
table as1;				# Define the tables
table as2;

protocol kernel kern1 {			# Synchronize them with the kernel
	table as1;
	kernel table 1;
}

protocol kernel kern2 {
	table as2;
	kernel table 2;
}

protocol bgp bgp1 {			# The outside connections
	table as1;
	local as 1;
	neighbor 192.168.0.1 as 1001;
	export all;
	import all;
}

protocol bgp bgp2 {
	table as2;
	local as 2;
	neighbor 10.0.0.1 as 1002;
	export all;
	import all;
}

protocol pipe {				# The Pipe
	table as1;
	peer table as2;
	export filter {
		if net ~ [ 1.0.0.0/8+] then {	# Only AS1 networks
			if preference>10 then preference = preference-10;
			if source=RTS_BGP then bgp_path.prepend(1);
			accept;
		}
		reject;
	};
	import filter {
		if net ~ [ 2.0.0.0/8+] then {	# Only AS2 networks
			if preference>10 then preference = preference-10;
			if source=RTS_BGP then bgp_path.prepend(2);
			accept;
		}
		reject;
	};
}
</code>

<sect>RIP

<sect1>Introduction

<p>The RIP protocol (also sometimes called Rest In Pieces) is a simple protocol, where each router broadcasts (to all its neighbors)
distances to all networks it can reach. When a router hears distance to another network, it increments
it and broadcasts it back. Broadcasts are done in regular intervals. Therefore, if some network goes
unreachable, routers keep telling each other that its distance is the original distance plus 1 (actually, plus
interface metric, which is usually one). After some time, the distance reaches infinity (that's 15 in
RIP) and all routers know that network is unreachable. RIP tries to minimize situations where
counting to infinity is necessary, because it is slow. Due to infinity being 16, you can't use
RIP on networks where maximal distance is higher than 15 hosts. You can read more about rip at <HTMLURL
URL="http://www.ietf.org/html.charters/rip-charter.html" TEXT="http://www.ietf.org/html.charters/rip-charter.html">. Both IPv4
and IPv6 versions of RIP are supported by BIRD, historical RIPv1 is
currently not fully supported.

<p>RIP is a very simple protocol, and it has a lot of shortcomings. Slow
convergence, big network load and inability to handle larger networks
makes it pretty much obsolete in IPv4 world. (It is still usable on
very small networks.) It is widely used in IPv6 networks,
because there are no good implementations of OSPFv3.

<sect1>Configuration

<p>In addition to options common for all to other protocols, RIP supports the following ones:

<descrip>
	<tag/authentication none|password|md5/ selects authentication method to be used. <cf/none/ means that
	  packets are not authenticated at all, <cf/password/ means that a plaintext password is embedded
	  into each packet, and <cf/md5/ means that packets are authenticated using a md5 cryptographic
	  hash. If you set authentication to not-none, it is a good idea to add <cf>passwords { }</cf>
	  section.

	<tag>honor always|neighbor|never </tag>specifies when should requests for dumping routing table
	  be honored. (Always, when sent from a  host on a directly connected
	  network or never.) Routing table updates are honored only from
	  neighbors, that is not configurable.
</descrip>

<p>There are two options that can be specified per-interface. First is <cf>metric</cf>, with
default one.  Second is <cf>mode multicast|broadcast|quiet|nolisten|version1</cf>, it selects mode for
rip to work in. If nothing is specified, rip runs in multicast mode. <cf>version1</cf> is
currently equivalent to <cf>broadcast</cf>, and it makes RIP talk to a broadcast address even
through multicast mode is possible. <cf>quiet</cf> option means that RIP will not transmit
any periodic messages to this interface and <cf>nolisten</cf> means that RIP will send to this
interface but not listen to it.

<p>The following options generally override behavior specified in RFC. If you use any of these
options, BIRD will no longer be RFC-compliant, which means it will not be able to talk to anything
other than equally configured BIRD. I have warned you.

<descrip>
	<tag>port <M>number</M></tag>
	  selects IP port to operate on, default 520. (This is useful when testing BIRD, if you
	  set this to an address &gt;1024, you will not need to run bird with UID==0).

	<tag>infinity <M>number</M></tag>
	  selects the value of infinity, default is 16. Bigger values will make protocol convergence
	  even slower.

	<tag>period <M>number</M>
	  </tag>specifies the number of seconds between periodic updates. Default is 30 seconds. A lower
	  number will mean faster convergence but bigger network
	  load. Do not use values lower than 10.

	<tag>timeout time <M>number</M>
	  </tag>specifies how old route has to be to be considered unreachable. Default is 4*<cf/period/.

	<tag>garbage time <M>number</M>
	  </tag>specifies how old route has to be to be discarded. Default is 10*<cf/period/.
</descrip>

<sect1>Attributes

<p>RIP defines two route attributes:

<descrip>
	<tag>int <cf/rip_metric/</tag> RIP metric of the route (ranging from 0 to <cf/infinity/).
	When routes from different RIP instances are available and all of them have the same
	preference, BIRD prefers the route with lowest <cf/rip_metric/.

	<tag>int <cf/rip_tag/</tag> RIP route tag: a 16-bit number which can be used
	to carry additional information with the route (for example, an originating AS number
	in case of external routes).
</descrip>

<sect1>Example

<p><code>
protocol rip MyRIP_test {
        debug all;
        port 1520;
        period 10;
        garbage time 60;
        interface "eth0" { metric 3; mode multicast; }
	          "eth1" { metric 2; mode broadcast; };
        honor neighbor;
        authentication none;
        import filter { print "importing"; accept; };
        export filter { print "exporting"; accept; };
}
</code>

<sect>Static

<p>The Static protocol doesn't communicate with other routers in the network,
but instead it allows you to define routes manually. This is often used for
specifying how to forward packets to parts of the network which don't use
dynamic routing at all and also for defining sink routes (i.e., those
telling to return packets as undeliverable if they are in your IP block,
you don't have any specific destination for them and you don't want to send
them out through the default route to prevent routing loops).

<p>There are three types of static routes: `classical' routes telling to
forward packets to a neighboring router, device routes specifying forwarding
to hosts on a directly connected network and special routes (sink, blackhole
etc.) which specify a special action to be done instead of forwarding the
packet.

<p>When the particular destination is not available (the interface is down or
the next hop of the route is not a neighbor at the moment), Static just
uninstalls the route from the table it is connected to and adds it again as soon
as the destination becomes adjacent again.

<p>The Static protocol has no configuration options. Instead, the
definition of the protocol contains a list of static routes:

<descrip>
	<tag>route <m/prefix/ via <m/ip/</tag> Static route through
	a neighboring router.
	<tag>route <m/prefix/ via <m/"interface"/</tag> Static device
	route through an interface to hosts on a directly connected network.
	<tag>route <m/prefix/ drop|reject|prohibit</tag> Special routes
	specifying to drop the packet, return it as unreachable or return
	it as administratively prohibited.
</descrip>

<p>Static routes have no specific attributes.

<p>Example static config might look like this:

<p><code>
protocol static {
	table testable;				# Connect to a non-default routing table
	route 0.0.0.0/0 via 62.168.0.13;	# Default route
	route 62.168.0.0/25 reject;		# Sink route
	route 10.2.0.0/24 via "arc0";		# Secondary network
}
</code>

<chapt>Problems

<p>BIRD is relatively young system, and probably contains some
bugs. You can report bugs at bird-users mailing list (<HTMLURL URL="mailto:bird-users@bird.network.cz" TEXT="bird-users@bird.network.cz">), but before you do,
please make sure you have read available documentation, make sure are running latest version (available at <HTMLURL
URL="ftp://bird.network.cz/pub/bird" TEXT="bird.network.cz:/pub/bird">). (Of course, patch
which fixes the bug along with bug report is always welcome). If you
want to use BIRD, join mailing list by sending
<tt/subscribe bird-users/ to <HTMLURL URL="mailto:majordomo@bird.network.cz" TEXT="majordomo@bird.network.cz">. Main home page of bird is <HTMLURL URL="http://bird.network.cz/" TEXT="http://bird.network.cz/">. When
trying to understand, what is going on, Internet standards are
relevant reading; you can get them from <HTMLURL URL="ftp://ftp.rfc-editor.org/" TEXT="ftp.rfc-editor.org"> (or nicely sorted version from <HTMLURL="ftp://atrey.karlin.mff.cuni.cz/pub/rfc" TEXT="atrey.karlin.mff.cuni.cz:/pub/rfc">.

<p><it/Good luck!/

</book>

<!--
LocalWords:  GPL IPv GateD BGPv RIPv OSPFv Linux sgml html dvi sgmltools Pavel
LocalWords:  linuxdoc dtd descrip config conf syslog stderr auth ospf bgp Mbps
LocalWords:  router's eval expr num birdc ctl unix if's enums bool int ip GCC
LocalWords:  len ipaddress pxlen netmask enum bgppath bgpmask clist gw md eth
LocalWords:  RTS printn quitbird iBGP AS'es eBGP RFC multiprotocol IGP Machek
LocalWords:  EGP misconfigurations keepalive pref aggr aggregator BIRD's
LocalWords:  OS'es AS's multicast nolisten misconfigured UID blackhole
LocalWords:  uninstalls ethernets IP
 -->